Spiral Wound Gaskets are extremely popular and widely used. A spiral wound Gasket is manufactured by spirally winding a performed metal strip and a filler on the outer periphery of metal winding mandrels. The winding mandrel outside diameter forms the inner diameter of the Gasket sand superposed metal and non-metallic windings are continually wound until the required outer diameter is attained. This engineered product is tailor made to be compatible with the flange closure in which it is to be used. They can be used over the complete temperature range from cryogenic to approximately 2000º degrees Fahrenheit. This type Gasket can be used in all pressures from vacuum to the standard 2500 PSI flange ratings. They are more resilient than any other type of metallic Gasket with the exception of pressure sealing metal Gaskets and, as a consequence, can compensate for flange movement that may occur due to temperature gradients, variations of pressure and vibration.

Types of Spiral Wound Gasket
Type R
Basic construction, inner and outer diameters are reinforced with several piles of metal without filler to give greater stability and better compression characteristics. Suitable for tongue and groove or male and female or grooved to flat face assemblies.

Type RIR
Solid inner metal ring acts as a compression stop and fills the annular space between flange bore and the inside diameter. Designed to prevent accumulation of solids, reduce turbulent flow of process fluids and minimize erosion of flange faces. Suitable for male and female pipe flanges.

Type CG
Utilizes an external ring which accurately centers Gasket on flange face: provides additional radial strength to prevent Gasket blowout and acts as a compression stop. A general purpose Gasket suitable for use with flat face and raised face flanges.

Type CGI
Suitable for use with flat face and raised face flanges and specified for high pressure/temperature service or where corrosive or toxic media are present. Note on use of inner rings: ASME B16.20 which covers spiral wound Gaskets requires the use of solid metal inner rings in Pressure Class 900, nominal pipe sizes 24" and larger, Pressure Class 1500, nominal pipe sizes 12" and larger, Pressure Class 2500, nominal pipe sizes 4" and larger, All PTFE filled Gaskets

Type HE
Type HE Gaskets are used for heat exchangers where pass bars may be required. The outer portion is of standard spiral wound construction, whereas the rib partition is normally of single or double jacketed Type, securely fastened to the I.D. of the spiral wound portion.

Type HE-CG
This Type is identical to the Type HE, except that it is fitted with an outer guide ring.

Type HE-CGI With Spiral Wound Outer Ring
The Type HE-CGI is a variation of the Type CGI spiral wound Gasket, developed for use on heat exchanger TEMA type flange arrangements. In conjunction with an inner ring, the standard spiral wound construction also supports an outer wound steel nose, designed for the purpose of accurate Gasket location. It is also available with solid metal outer ring.

Type CG-RJ
This Type designates a specially sized CG Gasket to be used on standard ring joint flanges. The outer ring is dimensioned to cover the ring joint grooves and to prevent the spiral wound portion from entering the groove. This type of Gasket should be used only as a maintenance repair item.

Type 625
Type 625 spiral wound Gaskets are similar to Type R Gaskets, with a thickness of 0.0625". These Gaskets are widely used wherever space restrictions indicate the need for a wafer thin Gasket design capable of sealing high pressures.

Type T
These Gaskets are used for boiler handhole and tube cap assemblies. They are available in round, oval, obround, square, pear and diamond shapes. Please note Type T Gaskets rely on internal pressure in the boiler to properly seat the Gasket. This means, when a hydrostatic test is performed on the Gasket, the pressure exerted against the plate will further compress the Gasket-and it is necessary to tighten each nut to compensate for the additional compression of the Gasket under load.

Type M, MC & MCS
These Types are designed for boiler manhole cover assemblies. They are usually round, obround or oval shape, depending of course , upon the manhole plate configuration. Type MC Gaskets have pre-formed inner and/or outer rings made of spiral windings. This centering guide permits the Gasket to assume its correct position and to compensate for inequalities in plate contours and fillets in cold-pressed plates as well as to prevent shouldering and pinching caused by radial misplacement. Type MCS Gaskets are manufactured with a solid metal inner and/or outer ring which also prevents over compression of the Gasket in high pressure systems.

Please use this channel to send us specific enquiries related to the products we deal with.
Since all properties, specifications and application parameters shown throughout this product information are approximate and may be mutually influenced, your specific application should not be undertaken without independent study and evaluation for suitability. All technical data and advice given is based on experiences Goodrich Gasket Private Limited has made so far. Failure to select proper sealing products can result in damage and/or personal injury. Properties, specifications and application parameters are subject to change without notice. Goodrich Gasket Private Limited does not undertake any liability of any kind whatsoever.